Saturday, June 17, 2017

Red Bronze KingPins

Hi Everyone,

Happy Father's Day weekend to you! After a week of beautiful weather we are getting some mixed skies and on and off rain again for the foreseeable future. At least it's finally warming up.

The Fidget Spinners were a big hit and thanks so much again for the huge and enthusiastic response. I am looking into possibly making more but I'm still not sure. I will keep you posted if it works out...In the meantime many other things are in the works and I am rapidly finishing projects up.

Today I have a small batch of Red Bronze KingPin tools ready. You'll notice that the heads have a very familiar 5 flute shape, but in a slimmer diameter (1/2") and longer length than the 5/8" diameter 5 flute Mega beads. The heads are tapered and drilled on one end to accept an 1/8" diameter pin and the exposed pin length is generous at just over 2 inches long. OAL of the tool is about 3 inches or so with the sheath. The pins are slip fit into the pin heads using green 680 Loctite so they are permanently set in place unless you were to heat it up with a torch.
 
The 5 Flute design works great for these tools as it provides well defined grip surfaces, and unlike other pin tools, these are totally anti roll so you can set it down and it absolutely will stay put. There is nothing more annoying than setting a small tool down for a moment and having it roll off the work surface.

The pins themselves are made of hardened steel which I have hand ground to a sharp point. Don't ask me what grade of steel it is as these are standard extra long dowel pins and the makers do not specify exact material, but they are definitely high carbon steel. Keep them wiped down and clean as they will probably rust. A few swipes with a worn green scotchbrite pad once in a while will make them as good as new though if rust spots do show up. And they are easily resharpened on a belt sander or grinding stone.

The KingPins come with a simple slip sheath of vinyl tubing. Once in the sheath they are perfectly safe to carry in a pocket or anywhere else. Keep the pin in the sheath at all times when you are not using it though as these are quite sharp and it would be very easy to puncture yourself. By all means, use common sense while using these and please, KEEP AWAY FROM CHILDREN!

I have been carrying mine for a few weeks and showing it around to see people's reaction. You can always tell which folks lack imagination when you see the uncertain look and blank expression followed by "What would you use that for?" Haha....a much better question would be "What wouldn't you use it for?"

I use mine all the time for mixing and applying two part epoxy. The pin performs perfectly and it is so easy to wipe clean. I have used it to mix a small jar of model paint for some touchups I needed to do. The pins excel at cord and knot work of course. Use them for all sorts of poking, prying and scraping tasks as well as cleaning duty to get into tight corners. They are great for helping to remove small bits of stuck on masking tape. I was using one just yesterday to pry a nasty old o-ring out of a groove. Leather people, woodworkers and craftsmen of all stripes will find endless and obvious uses for these tools. And, if you happen to have a balloon popping fetish, boy are you in luck! :)

I'll also be making more of these this summer in Zr, Titanium and Copper. Maybe a better fixture holder will allow for decorative hand stamps but for now these are ONLY available with the standard Atwood name stamp.

The bronze KingPins will run $60 plus shipping and it's one per customer with this small first batch. Don't worry if you miss today as I have a ton more of these on the way in other metals. As always, thanks for stopping in and have a great weekend.


Sold out for today, thank you so much folks! :)



















       

6 comments:

Zoltan said...

"And, if you happen to have a balloon popping fetish, boy are you in luck!".

Kendall Register said...

NO!!!! I was waiting for this one. Congrats to all who scored!

John said...

Wow those are great, nice tool!

Adam Kay said...

Great idea Peter, can't wait for the s/s or Ti versions to come!

SparkleSquash said...

what is the diameter of the pin Peter?

Peter Atwood said...

The pins are 1/8 inch in diameter.